PODGO XR IR RIG
10 Line 6 Pod Go presets - my 2026 signature rig, built around Tone Factor XR IRs (with permission) on the JMI 30/6 and Blankenship Twinplex. Five JMI and five Twinplex tones, each with humbucker and single coil versions, plus four snapshots: Clean, Drive, Boost/Lead, and Ambient.
These XR IR based presets were created with Kenyon's JMI 30/6 with Fane 100w Blues and his Blankenship Twinplex with the Supro BD-12 Cab. It is programmed as a plug-and-play rig that is loaded with dialed-in drives, modulation effects, delays, reverbs, and more.
PRESETS INCLUDED
KR JMI HB/SC 1 - ping pong delay & dynamic hall
KR JMI HB/SC 2 - harmonic trem & '63 spring
KR JMI HB/SC 3 - chorus & plate
KR JMI HB/SC 4 - memory man & tremolo
KR JMI HB/SC 5 - memory man & cave reverb
KR TWINPLEX HB/SC 1 - ping pong delay & dynamic hall
KR TWINPLEX HB/SC 2 - harmonic trem & '63 spring
KR TWINPLEX HB/SC 3 - chorus & plate
KR TWINPLEX HB/SC 4 - memory man & tremolo
KR TWINPLEX HB/SC 5 - memory man & cave reverb
SNAPSHOTS
CLEAN
DRIVE
BOOST/LEAD
AMBIENT
XR IRs INCLUDED
These presets include 2 XR IRs that were hand selected by me as my preference to build these presets with.
Be sure to place the correct IR with the correct amp type:
TF JMI 2x12 100w BLUE 545 3 - Enhanced (Essex A30)
TF SUPRO 2X12 BD12 545 3 - Enhanced (US Super Nrm)
FOOTSWITCH ASSIGNMENTS
these vary per preset and are custom catered to each effect within each preset but this is the general layout
VERB MIX
VERB bypass
DELAY bypass
DELAY TRAIL (repeats and mix)
BOOST
DRIVE
SNAPSHOTS
CLEAN
DRIVE
BOOST/LEAD
AMBIENT
UPDATE YOUR FIRMWARE [**IMPORTANT!**]
Ensure the firmware on your pedal & HX/POD GO Edit software is up to date before installing this preset. If your firmware or HX/POD GO Edit software is not up to date you will likely encounter an error when importing the presets onto your device. Both the pedal firmware and edit software must be up to date in order to load this preset without an error.
HOW TO IMPORT PRESETS & IMPULSE RESPONSES
This preset features tone-matched IRs that are to be loaded into the IR blocks.
Connect your pedal to your computer using a USB Cable.
Download and install the HX/Pod Go Edit app from Line 6
In the Edit app, drag and drop the preset into a slot in the ‘PRESETS’ column
To import the IRs, switch to the ‘IMPULSES’ column (next to the PRESETS column), and drag & drop the IRs into the slot of your choice to import it into the pedal (take note of what slot you dropped it into). Select the "IR" block in the preset and use the "IR Select" parameter to select the included IRs you just imported.
SAVE THE PRESET - if you don’t SAVE after loading the IRs in, you may get an IR error message every time you load the preset. Saving the preset will resolve that error.
Other IR Settings: MIX should be at 100%, the LEVEL, HIGH CUT and LOW CUT vary per preset are automatically saved with the preset.
RECOMMENDED POD GO GLOBAL SETTINGS
STOMP MODE: 6 switches (so you can toggle all effects on/off)
UP/DOWN SWITCHES: Banks
GUITAR IN PAD: our presets are dialed in with the input pad OFF. You should experiment with your guitar to see if you prefer it ON or OFF. If your guitar has hotter pickups and the amps are breaking up/distorting on a "clean" setting, try turning the Input pad ON in the global settings to lower/pad the input volume of your guitar. This will cause your guitar to not hit the amps as hard resulting in less breakup.
GLOBAL EQ: Off.
TAP TEMPO PITCH: Transparent (prevents pitch sifting when tapping a new tempo).
MAIN OUT LEVEL: Instrument (Line will be a hotter signal, and will easily clip/distort the input of your preamps/mixer/interface you are sending to).
MONO VS STEREO OPERATION
This preset can be used in either mono or stereo [recommended].
VERSION 1.0
FIRMWARE 2.50
Released 6/2026